2nd edition

### Errata

Below are a listing of known errors in the book’s first printing.

 Page No. Section Example/ Problem Figure Equation reference Original Correction 23 1.2.3 1.8 none none Using (1.67), we find for Vds = Veff = 0.4V, Using (1.67), we find for Vds = Veff = 0.35V, 23 1.2.3 1.8 none none In the case where VDS = Veff + 0.5V = 0.9V, we have In the case where VDS = Veff + 0.5V = 0.85V, we have 33 1.2.7 1.13 none none Cov = 2.0 x 10-4 pF/μm Cov‘ = 2.0 x 10-4 pF/μm 47 1.4.2 none 1.31 none In the plot of Id vs. Vgs, the slope of Id vs. Vgs in mobility degradation looks same as or larger than that of square law, which contradicts the plot of gm vs. Vgs Eliminate curvature on Id vs Vgs plot in mobility degradation. 53 1.5.3 none 1.33 none Two text labels include the “section end” character Replace with “/” 62 1.7.1 none none 1.146 Dn Dp 70 1.10.2 P1.12 none none The technology node and the values of Vdb, Vsb, and Cj-sw are not given Assume the 0.35μm CMOS technology, Vdb = Vsb = 0, and ignore sidewall capacitances. 101 2.3.3 none none none gm/ID = 1/(2Veff) gm/ID = 2/Veff 102 2.3.3 none none 2.19 σ2(ΔVGS) = 1/WL[AVt02(gm/ID)2 + AK’2] σ2(ΔVGS) = 1/WL[AVt02 + (ID/gm)2AK’2] 106 2.4.2 2.6 2.31 none left and right sides of the figure have been cropped left and right layout labels should indicate 10μm and 19.6μm dimensions respectively 124 3.4 none none none …, the input impedance, rout, is found to be 1/gm… …, the input impedance, rin, is found to be 1/gm… 140 3.11.2 P3.12 none none … shown in Fig. P3.11. … shown in Fig. P3.12. 145 4.1 none none none Further, the real parts of all the poles will be positive… Further, the real parts of all the poles will be negative… 148 4.1.2 4.2 none none … for the case f = 10 Hz, where ω = 2πf = 628.3 rad, … … for the case f = 10 Hz, where ω = 2πf = 62.83 rad, … 154 4.1.2 4.5 none 4.60 ∠A(ω) = -tan(ω/ω-3dB)-1 ∠A(ω) = -tan-1(ω/ω-3dB) 155 4.1.3 none none 4.70 Φ = -tan-1(ω/ωp1) – tan(ω/ωp2) Φ = -tan-1(ω/ωp1) – tan-1 (ω/ωp2) 161 4.1.4 4.7 none 4.93 1.05 x 108 rad/sec 1.05 x 1010 rad/sec 161 4.1.4 4.7 none 4.94 5 x 106 rad/sec 5 x 108 rad/sec 170 4.2.3 4.8 none none … to the case where Y(s) = 1/sC. … to the case where Y(s) = sC. 175 4.2.4 4.9 4.19 none gm1 labels should be beside the dependent current sources 176 4.2.4 4.10 none none use the transistor parameters listed in Table 1.5 for the 0.8-μm CMOS technology in Table 1.5. use the transistor parameters listed in Table 1.5 for the 0.8-μm CMOS technology. 176 4.2.4 4.10 none 4.158 the denominator of equation (4.152):Rin[Cgs1 + Cgs1(1 + gm1R2)] + R2(Cgd1 + C2) the denominator of equation (4.152):Rs[Cgs1 + Cgs1(1 + gm1R2)] + R2(Cgd1 + C2) 177 4.2.5 4.11 4.13 none L1=|Ao| l L1 Veff,1 L1=(|Ao| l L1 Veff,1) / 2 179 4.2.5 4.12 none none 2 x 355mA x 0.18μm / (270mA/V2 x (0.1V)2) 2 x 350mA x 0.18μm / (270mA/V2 x (0.1V)2) 191 4.4 4.16 none 4.212 = (4.27 x 109 rad/s = 2π x 680 MHz) = 4.27 x 109 rad/s = 2π x 680 MHz 194 4.5.1 none 4.31 none capacitor symbol overlaps the label, Cdb move capacitor symbol to the left 195 4.5.3 none none 4.226 negative sign in the numerator no negative sign in the numerator 196 4.5.3 none 4.34(a) none label “Vout” is mislocated move “Vout” label to the output below “RD“ 196 5.4.3 none 4.35 none dependent current source on the right points down dependent current source on the right points up 197 5.4.3 none 4.36 none dependent current source on the right points down dependent current source on the right points up 197 5.4.3 none 4.37 none dependent current source on the right points down dependent current source on the right points up 205 5.1.2 none none 5.7 ΔA / [(1+L)2+ ΔAβ] ΔA / [(1+L)2 + ΔAβ(1+L)] 209 5.2 5.3 none none In practice, the voltage at v– will increase above vin In practice, the voltage at v+ will increase above vin 210 5.2.1 none none none Key Point: “… -180 degres …” Key Point: “… -180 degrees …” 215 5.3.1 none none 5.29 Second equals sign: “=” Second equals sign should be approximately equals 216 5.3.1 5.6 5.9(b) none expression in the figure: “s/ωta“ expression in the figure: ” ωta/s” 217 5.3.1 5.6 none none … is well approximated by s/ωta. … is well approximated by ωta/s. 217 5.3.1 5.6 none 5.32 first term on right side: “(s/ ωta)” first term on right side: “(ωta /s)” 221 5.4 none none none Key Point: “… desired gain, β …” Key Point: “… desired gain, 1/ β …” 225 5.4.1 5.9 5.13(b) none arrow points down on the dependent source gm,1 arrow points up on the dependent source gm,1 225 5.4.1 5.9 5.13(c) none line connecting the tops of Zx and Cgs,5 is broken line connecting the tops of Zx and Cgs,5 should be connected 225 5.4.1 5.9 5.13(c) none Cgs,1/2 Cgs,1 /2 229 5.4.2 5.11 none none 2π 2.86MHz 2π 28.6MHz 235 5.5 none none none Key Point: “… -180 degres …” Key Point: “… -180 degrees …” 235 5.5 none none none Key Point: “… desired gain, β…” Key Point: “… desired gain, 1/β …” 244 6.1.1 6.1 none none We can calculate the transconductances of Q1, Q2, Q7 and Q8. We can calculate the transconductances of Q1, Q2, and Q7. 245 6.1.1 6.1 6.3 none Av1 Av2 = -1043 V/V or 60.4dB Av1 Av2 = 475 V/V or 53.5dB 248 6.1.2 6.3 none unnumbered ωp2 = 3.12mA/V / (5pF + 1pF) = 2π 82.8 MHz ωp2 = 3.12mA/V / 5pF = 2π 99.3 MHz 249 6.1.2 6.3 none unnumbered |ωp2| = 3.12mA/V / 5pF = 2π 99.3 MHz ωp2 = 3.12mA/V / 1pF = 2π 497 MHz 254 6.2.1 none none none …introduce an additional approximately +20° phase shift… …introduce an additional approximately +20° to 30° phase shift… 258 6.2.2 6.7 none none the opamp and ωz, ωp, and ω2 are the frequencies of a zero, the dominant pole, and the equivalent second pole, respectively. the opamp and ωz, ωp1, and ω2 are the frequencies of a zero, the dominant pole, and the equivalent second pole, respectively. 259 6.2.3 none none none Repeating equations (6.9) and (6.20) here, we have Repeating equations (6.42) with ß=1 and(6.20), we have 261 6.2.3 none none 6.71 lefthand side, denominator: Veff16 lefthand side, denominator: Veff9 268 6.4 none 6.19 none Dependent current source, Gmavi points down Dependent current source, Gmavi points up 279 6.5 6.11 none none the unity-gain frequency is increased by 150% the unity-gain frequency is increased by 100% 292 6.8 none 6.38 none Grounded nodes in the schematic These are AC grounds, and should be connected to a common-mode reference voltage 304 7.1.1 7.1(b) none none Vb = 1.1(450mV)+(200mV)/(0.9 √0.9) = 729mV Vb = 1.1(450mV)+(200mV)/(√0.9 √0.9) = 717mV 307 7.2.1 none 7.6 none Q13 size is 100 Q13 size is 25 309 7.2.1 none none none effective gate-source voltages increase by 27 percent effective gate-source voltages increase by 39 percent 309 7.2.2 none none none Q13 is five times greater … gate voltage of Q13 … Q14 is five times greater … gate voltage of Q14 … 310 7.2.2 none 7.8 none Resistor label “RB” Resistor label should use subscript: “RB“ 311 7.3.1 none none none Vbe will have approximately a -2mV/°K Vbe will have approximately a -2mV/K 313 7.3.1 7.4 none none For the special case of T0 = 300°K For the special case of T0 = 300K 313 7.3.1 7.4 none none at 300°K at 300K 313 7.3.1 7.4 none none Recalling that 0°K Recalling that 0K 314 7.3.1 7.4 none 7.29 8 mV/°K / 1.24V = 6.5×10-6 parts/°K = 6.5ppm/K 8 mV/K / 1.24V = 6.5×10-6 parts/K = 6.5ppm/K 314 7.3.2 none none none the same collector currents and collector-emitter voltages the same collector currents and collector-base voltages 317 7.3.2 none 7.13(b) none opamp positive terminal on top opamp positive terminal on bottom 318 7.3.2 7.5 none 7.51 Now, recalling from (7.26) that Now, recalling from (7.25) that 320 7.3.3 none 7.15 none Leftmost resistor is Ra Leftmost resistor is Ra/M 320 7.3.3 none 7.15 none Polarity of the opamp is incorrect with the positive terminal on the left Switch the polarity of the opamp so that positive terminal is on the right 325 7.4.3 7.6 none 7.74 RL/(rds1 + RL) -gm1R’L 326 7.4.3 7.6 7.21 none vgs,1 labeled incorrectly Should be labeled so that vgs,1 = v1 – vDD 326 7.4.3 7.6 7.21 none current source gm1 has wrong polarity reverse polarity of current source gm1 326 7.4.3 7.6 none 7.76 RL/(rds1 + RL) -gm1R’L 329 7.7.2 P7.7 none none Assume (W/L)12,13 = (2μm/0.2μm) and (W/L)12,13 = (8μm/0.2μm). Assume (W/L)14 = (2μm/0.2μm) and (W/L)15 = (8μm/0.2μm). 329 7.7.2 P7.10 none none an dc input a dc input 329 7.7.3 P7.12 and P7.13 none none 320°K 320K 330 7.7.4 P7.20(d) none none … so that ωpL ≈ ωpa/100? … so that ωpL ≈ ωpa/10? 361 8.9.1 8.2 P8.2 none Vdd=5V Vcc=5V 361 8.9.1 8.9 P8.9 none Vdd=5V Vcc=5V 371 9.2.3 9.4 none none Kv2=(50nV2) Kv2=(50nV)2 378 9.3.1 none none none temperature (300°K) temperature (300K) 383 9.3.6 9.8 none none temperature of 300°K temperature of 300K 392 9.4.2 9.11 none none i.e. 300°K i.e. 300K 400 9.5.2 none none none Δω = ω2 – ω Δω = ω2 – ω1 403 9.5.3 9.14 none none ID3 = 45 dB ID3 = -45 dB 408 9.8.2 P9.11 and P9.12 P9.11 and P9.12 none y-axis title: Vrms y-axis title: Vrms2 420 10.3 10.3 none none VDD = 1V VDD = 2V 420 10.3 10.3 none none -2.8mV charge injection; total of -56mV -28mV charge injection; total of 80mV 467 11.9.3 P11.11 none none Equation denominator: “Chld + Cbe6“ Equation denominator: “Chld + Cbe6 + CF“ 471 12.1.2 none none none independent of the feed-in gain, K1,2,3. independent of the feed-in gain, K0,1,2. 471 12.1.2 none none none determined by the feed-in gain, K1,2,3. determined by the feed-in gain, K0,1,2. 472 12.1.2 12.1 12.3 none 1/Q = √2 1/Q = -√2 477 12.2.4 none none 12.26 s(Gm3 / Cx+ Cb) s(Gm3 / Cx +CB) 478 12.2.4 none none 12.31 Gm3 / Cx+ Cb Gm3 / Cx +CB 482 12.3 12.5 none none For the case re,max < 0.01Re For the case re,max < 0.01Rs 482 12.3 none 12.13 none Gm = 1/Re Gm= 1/Rs 482 12.3 none 12.14 none Gm = 1/Re Gm = 1/Rs 510 12.8.1 12.10 12.41(b) none Vno Vpo 510 12.8.1 12.10 12.41(b) none Vpo Vno 536 12.13.4 P12.20 none none Sketch the resulting magnitude response |Vin(ω)/Vout(ω)| … Sketch the resulting magnitude response |Vout(ω)/Vin(ω)| … 554 13.6 13.8 none none at 40kHz and 60kHz is 0.2399 and 0.1559, at 40kHz and 60kHz is 0.2339T and 0.1559T, 568 14.2.3 none 14.13(a) none vco(nT-T) vco(nT-T/2) 568 14.2.3 none 14.13(b) none vci(nT-T/2) and vco(nT-T/2) vci(nT) and vco(nT) 571 14.3 none none none … a rms voltage Vc12(rms)= ÖkT/C … … a rms voltage Vc1 (rms)= ÖkT/C … 571 14.3 none none none … capacitor noise voltage Vc22(rms)= ÖkT/C. … capacitor noise voltage Vc2(rms)= ÖkT/C. 573 14.4 14.3 none none the bilinear transform p = (z-1) / (z+1) the bilinear transform s = (z-1) / (z+1) 574 14.4 none none none As in Example 14.2, As in Example 14.3, 577 14.4.2 none 14.21 none Φ1, Φ2 swap clock phases near C3: Φ2, Φ1 605 14.12.6 P14.20 none none ensure a dc offset of less than 5mV ensure a output dc offset of less than 5mV 605 14.12.6 P14.21 none none Find the resulting dc offset Find the resulting output dc offset 619 15.5.3 15.4 none none For the gain error, from (15.25) we have For the gain error, from (15.24) we have 627 16.1.2 none 16.4 none The LSB decoder at the bottom of the figure must also accept as input the digital signal b2 since the folded resistor-string changes direction. 642 16.5 none none none … employ an array of 2N-1 unitary … … employ an array of 2N-1 unitary … 669 17.4.1 17.7 none none V3 = 2(V2-Vref/4) = -540V V3 = 2(V2-Vref/4) = -540mV 669 17.4.1 17.7 none none Vin = 375mV Vin = 312.5mV 669 17.4.2 none none 17.42 Vin = Vref/2 (S(bi,0 + bi,1 – 1)2-i + bn-1,12N-2 +bN-1,02N-1) Vin = Vref/2 (S(bi,0 +bi,1 – 1)2-i + bn-1,12-N+2 +bN-1,02-N+1) 671 17.4.2 17.8 none none V2 = 2(V1 – V1x) = -200mV V2 = 2(V1 – V1,x) = -200mV 671 17.4.2 17.8 none none left-align the variables “b1,0“, “b1,1“, and “b2,1 b2,0” in the table 681 17.7 none 17.31 none The bottom of the resistor string is grounded. The bottom of the resistor string should be connected to an additional amplifier output that compares the input, Vin, to ground. 693 17.12.5 P17.22 none none the reference voltage supply Vref. the reference voltage supply Vref = 0.5V. 711 18.3.1 none none none f0 = 44.1 kHz 2f0 = 44.1 kHz 720 18.5.2 none none 18.44 RHS of 1st line: ŜTF2(z)X1(z) + N̂TF1(z)X2(z) ŜTF2(z)X1(z) – N̂TF1(z)X2(z) 720 18.5.2 none none 18.44 RHS of 2nd line: all terms are positive RHS of 2nd line: 3rd and 4th terms (those including N̂TF1) should be negative 720 18.5.2 none none 18.45 RHS: ŜTF2(z)STF1(z)E1(z) + N̂TF1(z)NTF2(z)E2(z) ŜTF2(z)STF1(z)E1(z) – N̂TF1(z)NTF2(z)E2(z) 722 18.6 none 18.23 none Modulator as drawn is unstable Modify H(z) so that z-2 appears in the feedback loop and there is no delay in the feedforward path. 729 18.8.4 none none 18.55 first term on the right-hand-side of the equals sign: U(z)z-1 U(z)z-1/(2-z-1) 729 18.8.4 none none 18.55 exponent in the 3rd and 4th terms on the right-hand side: (1-z-1)-2 (1-z-1)2 730 18.8.4 none 18.29 none Gain “1/2” appears between 2nd and 3rd summers at the top left of the figure To make it consistent with the reference [Hairapetian, 1994], the gain “1/2” should be moved to between 1st and 2nd summers at the top left of the figure 730 18.8.4 none 18.29 none box at lower-right hand corner, with Us(z) as its input, contradicts the reference [Hairapetian, 1994]: 2(1-z-1)2 2-z-1 742 19.1.3 19.1 19.3 and 19.4 none waveform labels: Vosc waveform labels: Vdiv 750 19.2.1 none 19.9 none caption: “(a) time-domain step response; (b) frequency domain jitter transfer function magnitude response” caption: “(a) frequency domain jitter transfer function magnitude response; (b) time-domain step response” 760 19.3 19.11 none none 1st and 3rd equations, second bracketed term includes “gm“ 1st and 3rd equations, second bracketed term, “gm1“ 760 19.3 19.11 none none 2nd equation, right-hand side: “nk / |Vs|” 2nd equation, RHS: “nk / |Vs| gm (Rd||ro1)” 760 19.3 19.11 none none 3rd equation, term preceding the brackets: “(Rd||ro1)2 / |Vs|2“ 3rd equation, term preceding the brackets: “1 / gm2 |Vs|2“ 778 19.5.2 19.19 none 19.95 denominator is incorrect 778 19.5.2 19.19 none 19.96 denominator: “2ωpll“ denominator: “4ωpll “ 784 19.8.3 P19.14 none none zero crossing times: “… 40.2ns, 41.0ns, 49.0 ns, …” zero crossing times: “… 40.2ns, 49.0 ns, …” End papers none none none none g = 2ID / Veff gm = 2ID / Veff End papers none none none none Endpaper CMOS technology parameter values differ slightly from those in Table 1.5. Posted problem solutions use the values in Table 1.5.

### 54 Responses to "Errata"

1. Øyvind says:

Section 18.3.1 (p.710) specifies fs=5.6448 MHz and f0=44.1 kHz to give an OSR=128. But per the definition of OSR used in the book (eq. 18.8), this should give an OSR=fs/(2*f0)=64. I assume the intention here might be to say 2*f0=44.1 kHz ?

1. TCC says:

Yes you are correct – thanks for the comment. I will add it to the errata.

2. Hesham says:

Section 7.3.3, Fig. 7.15, and Eq. (7.57):
The parameter “N” is not defined in the text.

1. TCC says:

Yes, this parameter is not explicitly defined. It is hopefully obvious to the reader that “N” refers to the number of diodes in parallel.

3. Hesham says:

There is an error in the errata. For the correction of the mistake in page 320 regarding opamp polarity, it is mentioned that the ref figure is “none”. The ref figure is Fig. 7.15. Please correct.

1. TCC says:

Fixed – thanks!

4. Hesham says:

Page 314, Section 7.3.2:
“both transistors have the same collector currents and collector-emitter voltages”
Should be “and collector-base voltages”.

1. TCC says:

Agreed – I have added this to the errata.

5. Hesham says:

Section 7.2.1, page 309, 2nd paragraph:
1) The reduction in mobility is 28%, not 27%.
2) If the mobility decreases by 28%, then Veff should be: Veff/0.72 = 1.39Veff –> Veff should increase by 39%, not 27%.

1. TCC says:

1) My calculation gave 0.2786 – a minor point!
2) Agreed – Veff should increase by 39%, not 27%. I have added this to the errata – thanks!

6. Hesham says:

Example 7.1-b)
ID is in inverse proportion to R.
BUT Veff is proportional to sqrt of ID rather than ID.
Thus, “0.9” should be replaced by “sqrt(0.9)”.
The correct answer should be 717mV

1. TCC says:

Yes – thank you! I’ve put this on the errata.

7. Hesham says:

In Section 7.2.2, second paragraph, third line, TWO occurrences:
Q13 should be replaced by Q14.

1. TCC says:

Right. The current density of Q14 is five times greater than that of Q4. Hence, the gate voltage of Q14 is suitable for use as the PMOS cascode bias Vcasc-p. Added to the errata – thank you!

8. charlie Li says:

page 420,Example 10.3, solution part:second line,”using (10.8),this …=-2.8mV”,i think it is “-28mV”,dose it mean: 2Vx1.4fF/101.4fF=2.8mV ?

1. TCC says:

Yes – you are correct. The charge injection due to overlap capacitance should be 27.6mV and so the total charge is found by adding 27.6mV and 52.7mV for a total of 80mV. I have added this to the errata.

9. Anders says:

On page 24(second ed.), you state that for a p-channel MOS to conduct, it must have VSG>Vtp, where Vtp is a negative quantity. So as a consequence, VSG=0 gives a conducting transistor since 0 is greater than any negative number, but this cannot be true ??

1. TCC says:

It is easy to get the signs confused in this context. Without having to get into the weeds of it myself, it is clear that your understanding of the matter is correct!

10. Rahul says:

Dear Professors,

The equations 5.2 and 5.3 in Chapter 5 should have a negative sign for the loop-gain term. If we set input to zero for loop-gain calculations, and follow the loop in Fig.5.1, v=-ABx and L=-AB, due to terminal v multiplying with -1. This also implies that there is a negative feedback. These equations should be included in the list of errata.

This book is one of my favorites and I liked this time in 2nd edition, topic of feedback was given more attention.

Thanks

1. TCC says:

The book adopts the more common convention of defining the loop gain of a negative feedback amplifier as positive (at low frequency). The signal x experiences gains of A and then B to the point V so the gain from X to V is AB not -AB. If one defines L=-AB, then all the equations of 5.4 and onward must also be modified.
V=ABX=AB(U-V) so V=U.AB/(1+AB) & Y=A(U-V) so Y=U.A/(1+AB)

11. Atanas Ganchev says:

In the solution of Example 5.1 on page 206 the change in the closed-loop gain should be less than 5%, because |4.9751-4.9975|=0.0224, which is 2.24% change.

1. TCC says:

The change in gain is expressed as a percentage of the originally computed gain. Hence,
|4.9751-4.9975|/4.9975 * 100 = 0.00448*100 = 0.45%

12. Claudio Talarico says:

I believe 4.133 is incorrect. It should be
wp2 = 1/(RS*(Cgs1+Cgd1))

4.133 is derived assuming C2 is large directly on 4.127,
However we cannot not use 4.127 directly (4.127 is based on the assumption that Cdg1*gm1*R2 >> R2*C2 which is in contradiction with the case we are considering in 4.132.

1. TCC says:

There is no contradiction in the most common cases.

The assumption of widely-spaced real poles which leads to (4.126) & (4.127) is tantamount to assuming the Miller capacitance, Cgd1*gm1*R2 >> C2. This is reasonable in the common case where Cgd1 includes a compensation capacitor Cc so that the Miller effect makes it much larger than C2.

Then, in order to arrive at (4.133) from (4.127), we assume C2 >> Cgs1, also reasonable assuming the opamp is loaded by a capacitance much bigger than Cgs1. This then allows us to neglect the term Cgs1*Cgd1 in the denominator of (4.128) as being much smaller than C2*Cgd1.

13. PHAT says:

Looking at equation 1.90 and example 1.13，I find Cov having different definitions.

1. TCC says:

Yes – you are correct. Example 1.13 should more properly refer to Cov‘, the overlap capacitance normalized per unit length of gate width. Hence, Cov = Cov‘ W. Thanks for catching this!

14. phatonic says:

In EXAMPLE 1.16,I have a question about the definition of Ioff. Only when VGS=0,we have Ioff. Then Ioff has nothing to do with the changes of VGS,and it is a function of vth. Is that Right,Dr Carusone?

1. TCC says:

Yes – your interpretation is consistent with equation (1.121). This definition is particularly suitable for CMOS digital logic circuits where the MOSFETs act as switches that are OFF when VGS = 0. In analog circuits, sometimes the source (and even the body terminal) may not be at ground. It may be possible to reduce subthreshold leakage in these cases by decreasing VGS even further, below zero. Thanks for raising this confusing point!

15. Travis says:

The second pole and zero frequency is incorrect in example 4.7 on page 159-163. The circuit shows 1pF, but the calculations must have used 100pF, because the frequency is off by 100.

1. TCC says:

Thanks very much for catching this. It’s now reflected in the errata.

16. Michael says:

On page 182,Equation4.168 Rout is rds2//RL.I think Rout is gm2rds2rds1//RL;
Equation4.170,gs2=1/rs2=gin2+gds1,gin2 I think is gm2;
Equation4.171 I think gin2 is gm2 too.

1. TCC says:

Equation (4.168) refers to rd2 which is the small-signal resistance seen looking into the drain of Q2, not simply rds2 as you suggest. The substitution for rd2 is then made in (4.174). In equations (4.170) and (4.171), note that gin2 is approximately gm2, but is more accurately given by the expression in (4.160) which takes into account the circuit’s finite load impedance.

17. zeynep says:

Page 124, last paragraph, first sentence:
“…, the input impedance, rout, is found to be 1/gm…” -> rout should be rin.

18. Simon says:

Equation 6.71, page 261. It says Veff7 / Veff16 = …
I assume it should be Veff7 / Veff6? (since there’s not even a Q16).

1. TCC says:

No, not quite, although of course there is a typo there. In fact, in equation (6.71) Veff16 should be replaced by Veff9, the triode device realizing Rc. Thanks.

19. Chi says:

On page 420, example 10.3.
There’s a print error on Vdd=1V which should be 2V according to the solution below.

20. awuesiak says:

Equation 1.146: I think there should be Dp instead of Dn

21. sevil says:

Page 197 Figure 4.37: Dependent current source arrow direction should be up in order to model + gain of the active load diff. pair.

22. sevil says:

Page 196 Fig. 4.35 right-hand side dependent current source arrow should be upwards since vgs2=-vg1/2. Then page 195 Eqn. 4.226 becomes positive.

23. Ned says:

Figure 7.13 – Based on Ye’s Paper, the terminals of OP-AMP are incorrectly connected. Should they not be reversed.

1. TCC says:

Yes – for Fig. 7.13(b) only they should be reversed in order to provide negative feedback, and in accordance with Ye’s paper. Fig. 7.13(a) is correct as is. Thanks!

24. sevil says:

Page 510, Ex. 12.10, Fig. 12.41(b): Output differential voltage polarization should be reversed in order to have a negative gain of (-1/(sRC)) as stated in the solution.

25. zeynep says:

Page 225 example 4.9 solution:
Fig. 5.13b: simplified small-signal model of the diff pair’s dependent current source direction should be reversed (Av=+gm*Rout).
Then Fig. 5.13c becomes correct for dependent current source:
gm1(Vin-Vout)”up arrow”
= gm1(0-Vt) “up arrow”
=-gm1*Vt “up arrow”
= gm1*Vt “down arrow”

26. zeynep says:

Page 170 example 4.8 solution:

In the first sentence, Miller feedback admittance is stated as “Y(s)=1/sC”,which should be Y(s)=sC.

27. Sheng says:

polarity of opamp on fig 7.15 is wrong!!!

28. angbong says:

on page 446 says Since this charge is negative, it will cause the junction voltages to have negative glitches.
i think positive charge is right since switch of Fig.11.3 is PMOS transistor.

1. TCC says:

I think you are confused by the symbol in Fig. 11.3. In that figure, Q1 is in fact an NMOS transistor, as indicated by the arrowhead.

29. Cod says:

In p.145 sec. 4.1 last sentence in last paragraph.
“Further, the real parts of all the poles will be positive for stable transfer functions.”
The term “positive” should be modified as “negative”!

30. Noel says:

I noticed that on page 148 that with f=10Hz, ω = 2πf = 62.83 rad/s and not 628.3 rad/s

31. Noel says:

The caption on Fig 4.1 on page 151 says lowpass circuit but the circuit is a highpass.

1. TCC says:

In fact, the transfer function for Vin/Vout of that circuit is, indeed, lowpass. You may find the analysis in Example 4.3.

2. Ping says:

The H(s) in the Ex. 4.3 is a high-pass filter, sRC/(1+sRC). Which part of the example shows a low-pass transfer function? I got a little confused by this. The basic formula looks like low-pass, but as the circuit transfer function derives, it is clear a high-pass filter, doesn’t it? Thank you.

1. TCC says:

The capacitor acts like open circuit at DC and short circuit to ground at very high frequencies. So the circuit will pass the DC content and the capacitor will attenuate the signal at very high frequencies. This result can also be confirmed with mathematical transfer function of the circuit:
The transfer function is just a voltage divider between the capacitor and the resistor impedances:
H(s) = (1/Cs) / (R+1/Cs) = 1/(1+RCs)
which is a lowpass transfer function. (If you replace s=0 for DC: H=1; and if you replace s=infinity: H=0)

32. Phil says:

Equation (2.19)
It should be identical with Eq. (2.18)
σ^2(∆VGS) = … = 1/WL[Avt0^2+(ID/gm)^2*(Ak’^2)]